[Apr-2026] NSE5_FNC_AD_7.6 Dumps are Available for Instant Access using PracticeTorrent
NSE5_FNC_AD_7.6 Dumps 2026 - New Fortinet NSE5_FNC_AD_7.6 Exam Questions
Fortinet NSE5_FNC_AD_7.6 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 4 |
|
| Topic 5 |
|
NEW QUESTION # 17
A user was attempting to register their host through the registration captive portal. After successfully registering, the host remained in the registration VLAN. Which two conditions would cause this behavior? (Choose two.)
- A. The wrong agent s installed.
- B. The port default VLAN is the same as the Registration VLAN.
- C. There is no agent installed on the host.
- D. There is another unregistered host on the same port
Answer: B,D
Explanation:
The process of moving a host from a Registration VLAN to a Production VLAN (Access VLAN) is a fundamental part of the FortiNAC-F "VLAN steering" workflow. When a host successfully registers via the captive portal, FortiNAC-F evaluates its Network Access Policies to determine the correct VLAN. If the host remains stuck in the Registration VLAN despite a successful registration, it is typically due to port-level restrictions or the presence of other unregistered devices.
The two most common reasons for this behavior as per the documentation are:
The port default VLAN is the same as the Registration VLAN: If the "Default VLAN" field in the switch port's model configuration is set to the same ID as the Registration VLAN, the port will not change state because FortiNAC-F believes it is already in its "normal" or "forced" state.
There is another unregistered host on the same port: FortiNAC-F maintains the security posture of the physical port. If multiple hosts are connected to a single port (e.g., via a hub or unmanaged switch) and at least one host remains "Rogue" (unregistered), FortiNAC-F will generally keep the entire port in the isolation/registration VLAN to prevent the unregistered host from gaining unauthorized access to the production network.
Issues with agents (A, B) typically prevent a host from completing compliance or registration but do not usually result in a "stuck" status after registration has already been marked as successful in the system.
"If a port is identified as having Multiple Hosts, and those hosts require different levels of access, FortiNAC remains in the most restrictive state (Registration or Isolation) until all hosts on that port are authorized... Additionally, verify the Default VLAN setting for the port; if the Default VLAN and Registration VLAN match, the system will not trigger a VLAN change upon registration." - FortiNAC-F Administration Guide: Troubleshooting Host Management.
NEW QUESTION # 18
An administrator wants to control user access to corporate resources by integrating FortiNAC-F with FortiGate using firewall tags defined on FortiNAC-F.
Where would the administrator assign the firewall tag value that will be sent to FortiGate?
- A. Security rule
- B. RADIUS group attribute
- C. Device profiling rule
- D. Logical network
Answer: D
Explanation:
Questio ns no: 9
Verified Answe r: B
Comprehensive and Detailed 250 to 300 words each Explanation with Exact Matched Extract from FortiNAC-F Administrator library and documentation for current versions (including F 7.2, 7.4, and 7.6) documents:
In FortiNAC-F, the integration with FortiGate for Security Fabric and Single Sign-On (FSSO) allows the system to communicate the access level of an endpoint directly to the firewall using firewall tags. This eliminates the need for complex VLAN steering in some environments by allowing the FortiGate to apply policies based on these dynamic tags instead of just a physical or virtual network segment.
The actual assignment of the firewall tag value occurs within a Logical Network. In the FortiNAC-F architectural model, a Logical Network acts as a container for "Access Values". When an administrator configures a Logical Network (located under Network > Logical Networks), they define what that network represents-such as "Corporate Access" or "Contractor Limited". Within that definition, they assign the specific Firewall Tag that matches the tag created on the FortiGate. Once a user or host matches a Network Access Policy, FortiNAC-F identifies the associated Logical Network and pushes the defined tag to the FortiGate via the FSSO connector.
It is important to note that while Network Access Policies (and by extension Security Rules) are the logic engines that trigger the assignment, they do not hold the tag value itself. They simply point to a Logical Network, which serves as the central repository for that specific access configuration.
"To assign firewall tags, navigate to Network > Logical Networks. Select the desired logical network and click Edit. Under the Access Value section, select Firewall Tag as the type and enter the tag name exactly as it appears on the FortiGate. When a Network Access Policy matches a host, FortiNAC sends this tag to the FortiGate as an FSSO message." - FortiNAC-F Administration Guide: Logical Networks and Security Fabric Integration.
NEW QUESTION # 19
When FortiNAC-F is managing VPN clients connecting through FortiGate, why must the clients run a FortiNAC-F agent?
- A. To validate the endpoint policy compliance
- B. To collect user authentication details
- C. To transparently update The client IP address upon successful authentication
- D. To collect the client IP address and MAC address
Answer: D
Explanation:
When FortiNAC-F manages VPN clients through a FortiGate, the agent plays a fundamental role in device identification that standard network protocols cannot provide on their own. In a standard VPN connection, the FortiGate establishes a Layer 3 tunnel and assigns a virtual IP address to the client. While the FortiGate sends a syslog message to FortiNAC-F containing the username and this assigned IP address, it typically does not provide the hardware (MAC) address of the remote endpoint's physical or virtual adapter.
FortiNAC-F relies on the MAC address as the primary unique identifier for all host records in its database. Without the MAC address, FortiNAC-F cannot correlate the incoming VPN session with an existing host record to apply specific policies or track the device's history. By running either a Persistent or Dissolvable Agent, the endpoint retrieves its own MAC address and communicates it directly to the FortiNAC-F service interface. This allows the "IP to MAC" mapping to occur. Once FortiNAC-F has both the IP and the MAC, it can successfully identify the device, verify its status, and send the appropriate FSSO tags or group information back to the FortiGate to lift network restrictions.
Furthermore, while the agent can also perform compliance checks (Option D), the architectural requirement for the agent in a managed VPN environment is primarily driven by the need for session data correlation-specifically the collection of the IP and MAC address pairing.
"Session Data Components: * User ID (collected via RADIUS, syslog and API from the FortiGate). * Remote IP address for the remote user connection (collected via syslog and API from the FortiGate and from the FortiNAC agent). * Device IP and MAC address (collected via FortiNAC agent). ... The Agent is used to provide the MAC address of the connecting VPN user (IP to MAC)." - FortiNAC-F FortiGate VPN Integration Guide: How it Works Section.
NEW QUESTION # 20
An administrator wants to build a security rule that will quarantine contractors who attempt to access specific websites.
In addition to a user host profile, which Iwo components must the administrator configure to create the security rule? (Choose two.)
- A. Trigger
- B. Security String
- C. Methods
- D. Action
- E. Endpoint compliance policy
Answer: A,D
Explanation:
In FortiNAC-F, the Security Incidents engine is used to automate responses to security threats reported by external devices. When an administrator wants to enforce a policy, such as quarantining contractors who access restricted websites, they must create a Security Rule. A Security Rule acts as the "if-then" logic that correlates incoming security data with the internal host database.
The documentation specifies that a Security Rule consists of three primary configurable components:
User/Host Profile: This identifies who or what the rule applies to (in this case, "Contractors").
Trigger: This is the event that initiates the rule evaluation. In this scenario, the Trigger would be configured to match specific syslog messages or NetFlow data indicating access to prohibited websites. Triggers use filters to match vendor-specific data, such as a "Web Filter" event from a FortiGate.
Action: This defines what happens when the Trigger and User/Host Profile are matched. For this scenario, the administrator would select a "Quarantine" action, which instructs FortiNAC-F to move the endpoint to a restricted VLAN or apply a restrictive ACL.
While "Methods" (A) relate to authentication and "Security Strings" (E) are used for specific SNMP or CLI matching, they are not the structural components of a Security Rule in the Security Incidents menu.
"Security Rules are used to perform a specific action based on certain criteria... To configure a Security Rule, navigate to Logs > Security Incidents > Rules. Each rule requires a Trigger to define the event criteria, an Action to define the automated response (such as Quarantine), and a User/Host Profile to limit the rule to specific groups." - FortiNAC-F Administration Guide: Security Rules and Incident Management.
NEW QUESTION # 21
Refer to the exhibit.
What will happen to the host of a guest user created from this template if the time of connection is 8:00 PM?
- A. The host will be marked as at-risk.
- B. The host will be marked as non-authenticated.
- C. The host will be administratively disabled.
- D. The host will be marked as a rogue device.
Answer: B
Explanation:
In FortiNAC-F, the Guest & Contractor Template is a configuration object that defines the parameters for accounts created by sponsors or through self-registration. One of the critical security controls within this template is the Login Availability setting. This setting restricts the specific days and times during which a guest or contractor is permitted to authenticate and access the network.
As shown in the exhibit, the "StandardGuest" template has Login Availability set to "Specify Time", with a schedule defined as Mon-Fri, 6:00 AM to 7:00 PM. If a guest user attempts to connect or authenticate at 8:00 PM, which is outside of the permitted window, FortiNAC-F's policy engine will automatically deny the authentication request. When an authentication attempt is denied due to schedule restrictions, the system does not move the host into the "Authenticated" or "Registered" state required for production access. Instead, the host is marked as non-authenticated in the adapter or host view.
This behavior ensures that even if a guest possesses valid credentials, their access is strictly bound by the organizational policy for visitor hours. The host will typically remain in its current isolation or registration VLAN, and the user will see a message on the captive portal indicating that their account is not currently authorized for login. It is important to distinguish this from "at-risk" (C), which relates to security scan failures, or "rogue" (B), which typically refers to unknown devices that have not yet been associated with a valid account or profiling rule.
"Login Availability defines the timeframe during which the guest or contractor account is valid for network access. This schedule is enforced at the time of authentication. If a user attempts to log in outside of the designated window, the authentication is rejected by the system. Consequently, the host record will reflect a non-authenticated status, and the device will remain restricted to the isolation or registration network until a valid login window is reached." - FortiNAC-F Administration Guide: Guest and Contractor Templates Section.
NEW QUESTION # 22
In which three ways would deploying a FortiNAC-F Manager into a large environment consisting of several FortiNAC-F CAs simplify management? (Choose three.)
- A. Pooled licenses
- B. Global version control
- C. Global visibility
- D. Global infrastructure device inventory
- E. Global authentication security policies
Answer: A,B,C
Explanation:
The FortiNAC-F Manager (FortiNAC-M) is designed as a centralized management platform for large-scale distributed environments where multiple FortiNAC-F Control and Application (CA) appliances are deployed across different sites. According to the FortiNAC-F Manager Administration Guide, the deployment of a Manager simplifies administrative overhead in three specific ways:
First, it provides Global Version Control (B). The Manager serves as a central repository for firmware and software updates, allowing administrators to push specific versions to all managed CAs simultaneously, ensuring consistency across the entire fabric. Second, it enables Pooled Licenses (D). Instead of purchasing and managing individual licenses for every CA, licenses are centralized on the Manager. The Manager then distributes these licenses to the CAs as needed based on their host counts. This "floating" license model optimizes cost and prevents individual sites from running out of capacity while others have excess. Third, it offers Global Visibility (E). The Manager aggregates host and device data from every managed CA into a single console. This "single pane of glass" allows an administrator to search for a specific MAC address or user across the entire global organization without logging into individual servers.
While the Manager can assist with configuration templates, authentication security policies (C) and infrastructure modeling (A) are still predominantly managed at the local CA level to ensure site-specific logic and performance.
"The FortiNAC Manager provides a central management console for multiple FortiNAC-F servers (CAs). Key benefits include: * License Management: Licenses are pooled on the Manager and allocated to managed CAs as needed. * Software Management: Firmware updates can be centrally managed and pushed to all CAs from the Manager. * Centralized Monitoring: Provides a global view of all hosts, adapters, and events across the entire managed environment." - FortiNAC-F Manager Administration Guide: Overview and Benefits.
NEW QUESTION # 23
How can an administrator configure FortiNAC-F to normalize incoming syslog event levels across vendors?
- A. Configure event to alarm mappings.
- B. Configure the vendor OUI settings.
- C. Configure severity mappings.
- D. Configure the security rule settings.
Answer: C
Explanation:
FortiNAC-F serves as a central manager for security events originating from a diverse ecosystem of third-party security appliances, such as FortiGate, Check Point, and Cisco. Each vendor utilizes its own internal scale for severity levels within syslog messages (e.g., Check Point uses a 1-5 scale, while others may use 0-7). To provide a consistent response regardless of the source, FortiNAC-F uses Severity Mappings to normalize these incoming values.
According to the FortiNAC-F Administration Guide, severity mappings allow the administrator to translate vendor-specific threat levels into standardized FortiNAC Security Levels (such as High, Medium, or Low Violation). When a syslog message arrives, the parser extracts the vendor's severity code, and the system immediately references the Security Event Severity Level Mappings table to determine how that event should be categorized internally. This normalization is vital because it allows a single Security Alarm to be configured to respond to any "High Violation" event, whether it was reported as a "Critical" by one vendor or a "Level 5" by another. Without these mappings, the administrator would have to create separate, redundant security rules for every vendor to account for their different naming conventions and numerical scales.
"Each vendor defines its own severity levels for syslog messages. The following table shows the equivalent FortiNAC security level... To normalize these events, configure the Severity Level Mappings found in the device integration guides. This allows FortiNAC to generate a consistent security event that can then trigger an alarm regardless of the reporting vendor's specific terminology." - FortiNAC-F Administration Guide: Vendor Severity Levels and Syslog Management.
NEW QUESTION # 24
While discovering network infrastructure devices, a switch appears in the inventory topology with a question mark (?) on the icon. What would cause this?
- A. A read-only SNMP community siring was used.
- B. SNMP is not enabled on the switch.
- C. The SNMP ObjectlD is not recognized by FortiNAC-F.
- D. The wrong SNMP community string was entered during discovery.
Answer: C
Explanation:
In FortiNAC-F, the Inventory topology uses specific icons to represent the status and model of discovered network infrastructure. When a switch or other network device is discovered via SNMP, FortiNAC-F retrieves its System ObjectID (sysObjectID) to identify the specific make and model. This OID is then compared against the internal database of supported device mappings.
A question mark (?) icon appearing on a discovered switch indicates that while the discovery process successfully communicated with the device (meaning SNMP credentials were correct), the SNMP ObjectID is not recognized or mapped in the current version of FortiNAC-F. This essentially means the device is "unsupported" by the current software out-of-the-box. Because the OID is unknown, FortiNAC-F does not know which CLI or SNMP command set to use for critical functions like L2 polling (host visibility) or VLAN switching (enforcement). To resolve this, an administrator can manually "Set Device Mapping" to a similar existing model or a "Generic SNMP Device" if only basic L3 visibility is required.
"Discovered devices displaying a '?' icon indicate the currently running version does not have a mapping for that device's System OID (device is not supported). Device mappings are used to manage the device by performing functions such as L2/L3 Polling, Reading, and Switching VLANs." - Fortinet Technical Tip: Options for devices unable to be modeled in Inventory.
NEW QUESTION # 25
Refer to the exhibit.
A FortiNAC-F N+1 HA configuration is shown.
What will occur if CA-2 fails?
- A. CA-3 will be promoted to a primary and share management responsibilities with CA-1.
- B. CA-3 will continue to operate as a secondary in an N+1 HA configuration.
- C. CA-3 will be promoted to a primary and FortiNAC-F manager will load balance between CA-1 and CA-3.
- D. CA-1 and CA-3 will operate as a 1+1 HA cluster with CA-3 acting as a hot standby.
Answer: B
Explanation:
In an N+1 High Availability (HA) configuration, a single secondary Control and Application (CA) server provides backup for multiple primary CA servers. The FortiNAC-F Manager (FortiNAC-M) acts as the centralized orchestrator for this cluster, monitoring the health of all participating nodes.
According to the FortiNAC-F 7.6.0 N+1 Failover Reference Manual, when a primary CA (such as CA-2 in the exhibit) fails, the secondary CA (CA-3) is automatically promoted by the Manager to take over the specific workload and database functions of that failed primary. Crucially, the documentation specifies that even after this promotion, the system architecture maintains its N+1 logic. The secondary CA effectively "assumes the identity" of the failed primary while continuing to operate within the N+1 framework established by the Manager.
It does not merge with CA-1 to form a traditional 1+1 active/passive cluster (A), nor does it engage in load balancing (D), as FortiNAC-F HA is designed for redundancy and failover rather than active traffic distribution. Furthermore, CA-3 does not "share" management with CA-1 (C); it independently handles the tasks originally assigned to CA-2. Throughout this failover state, the Manager continues to oversee the group, and CA-3 remains the designated secondary unit currently acting in a primary capacity for the downed node until CA-2 is restored.
"In an N+1 Failover Group, the Secondary CA is designed to take over the functionality of any single failed primary component within the group. The FortiNAC Manager monitors the primaries and initiates the failover to the secondary... Once failover occurs, the secondary continues to operate as the backup unit for the failed primary while remaining part of the managed N+1 HA configuration." - FortiNAC-F 7.6.0 N+1 Failover Reference Manual: Failover Behavior Section.
NEW QUESTION # 26
Refer to the exhibit.
An administrator wants to use FortiNAC-F to automatically provision printers throughout their organization. Each building uses its own local VLAN for printers.
Which FortiNAC-F feature would allow this to be accomplished with a single network access policy?
- A. Dynamic host groups
- B. Logical networks
- C. Device profiling rules
- D. Preferred VLAN designations
Answer: B
Explanation:
The FortiNAC-F Logical Network feature is specifically designed to provide an abstraction layer between high-level security policies and the underlying physical network infrastructure. In large-scale deployments where different physical locations (like Building 1, 2, and 3 in the exhibit) use different local VLAN IDs for the same type of device (e.g., VLAN 10, 20, and 30 for printers), managing separate policies for each building would create significant administrative overhead.
By using a Logical Network, an administrator can create a single entity-for example, a logical network named "Printers"-and use it as the "Access Value" in a single Network Access Policy. The mapping of this logical label to a specific physical VLAN occurs at the Model Configuration level for each network device. When a printer connects to a switch in Building 1, FortiNAC-F evaluates the policy, identifies that the printer should be in the "Printers" logical network, and checks the Model Configuration for that specific switch to see which VLAN ID is mapped to that label (VLAN 10). If the same printer moves to Building 3, the same single policy applies, but FortiNAC-F provisions it to VLAN 30 based on the local mapping for that building's switch.
This architectural approach ensures that policies remain consistent and easy to manage regardless of the complexity or variations in the local network topology.
"Logical Networks provide a way to define a network access requirement once and apply it across many different network devices that may use different VLAN IDs for that access... Each managed device can use different VLAN IDs for the same Logical Network label. You can define the Logical Networks based on requirements and then associate the network to a VLAN ID when the managed device is configured in the Model Configuration." - FortiNAC-F IoT Deployment Guide: Define the Logical Networks.
NEW QUESTION # 27
A network administrator is troubleshooting a network access issue for a specific host. The administrator suspects the host is being assigned a different network access policy than expected.
Where would the administrator look to identify which network access policy, if any, is being applied to a particular host?
- A. The Port Properties view of the hosts port
- B. The Connections view
- C. The Policy Logs view
- D. The Policy Details view for the host
Answer: D
Explanation:
When troubleshooting network access in FortiNAC-F, it is often necessary to verify exactly why a host has been granted a specific level of access. Since FortiNAC-F evaluates policies from the top down and assigns access based on the first match, an administrator needs a clear way to see the results of this evaluation for a specific live endpoint.
The Policy Details (C) view is the designated tool for this purpose. By navigating to the Hosts > Hosts (or Adapter View) in the Administration UI, an administrator can search for the specific MAC address or IP of the host in question. Right-clicking on the host record reveals a context menu from which Policy Details can be selected. This view provides a real-time "look" into the policy engine's decision for that specific host, showing the Network Access Policy that was matched, the User/Host Profile that triggered the match, and the resulting Network Access Configuration (VLAN/ACL) currently applied.
While Policy Logs (A) provide a historical record of all policy transitions across the system, they are often too high-volume to efficiently find a single host's current state. The Connections view (B) shows the physical port and basic status but lacks the granular policy logic breakdown. The Port Properties (D) view shows the configuration of the switch interface itself, which is only one component of the final access determination.
"To identify which policy is currently applied to a specific endpoint, use the Policy Details view. Navigate to Hosts > Hosts, select the host, right-click and choose Policy Details. This window displays the specific Network Access Policy, User/Host Profile, and Network Access Configuration currently in effect for that host record." - FortiNAC-F Administration Guide: Policy Details and Troubleshooting.
NEW QUESTION # 28
A network administrator is troubleshooting a network access issue for a specific host. The administrator suspects the host is being assigned a different network access policy than expected.
Where would the administrator look to identify which network access policy, if any, is being applied to a particular host?
- A. The Port Properties view of the hosts port
- B. The Connections view
- C. The Policy Logs view
- D. The Policy Details view for the host
Answer: D
Explanation:
When troubleshooting network access in FortiNAC-F, it is often necessary to verify exactly why a host has been granted a specific level of access. Since FortiNAC-F evaluates policies from the top down and assigns access based on the first match, an administrator needs a clear way to see the results of this evaluation for a specific live endpoint.
The Policy Details (C) view is the designated tool for this purpose. By navigating to the Hosts > Hosts (or Adapter View) in the Administration UI, an administrator can search for the specific MAC address or IP of the host in question. Right-clicking on the host record reveals a context menu from which Policy Details can be selected. This view provides a real-time "look" into the policy engine's decision for that specific host, showing the Network Access Policy that was matched, the User/Host Profile that triggered the match, and the resulting Network Access Configuration (VLAN/ACL) currently applied.
While Policy Logs (A) provide a historical record of all policy transitions across the system, they are often too high-volume to efficiently find a single host's current state. The Connections view (B) shows the physical port and basic status but lacks the granular policy logic breakdown. The Port Properties (D) view shows the configuration of the switch interface itself, which is only one component of the final access determination.
"To identify which policy is currently applied to a specific endpoint, use the Policy Details view. Navigate to Hosts > Hosts, select the host, right-click and choose Policy Details. This window displays the specific Network Access Policy, User/Host Profile, and Network Access Configuration currently in effect for that host record." - FortiNAC-F Administration Guide: Policy Details and Troubleshooting.
NEW QUESTION # 29
A healthcare organization is integrating FortiNAC-F with its existing MDM. Communication is failing between the systems.
What could be a probable cause?
- A. SOAP API communication is failing
- B. Security Fabric traffic is failing
- C. SSH communication is failing
- D. REST API communication is failing
Answer: D
Explanation:
The integration between FortiNAC-F and Mobile Device Management (MDM) platforms (such as Microsoft Intune, VMware Workspace ONE, or Jamf) is a critical component for providing visibility into mobile assets that do not connect directly to the managed infrastructure via standard wired or wireless protocols.
According to the FortiNAC-F MDM Integration Guide, the communication between the FortiNAC-F appliance and the MDM server is handled through REST API calls. FortiNAC-F acts as an API client, periodically polling the MDM server to retrieve device metadata, compliance status, and ownership information. If communication is failing, it is most likely because the API credentials (Client ID/Secret) are incorrect, the MDM's API endpoint is unreachable from the FortiNAC-F service port, or the SSL certificate presented by the MDM is not trusted by the FortiNAC-F root store.
While SSH (B) is used for switch CLI management and the Security Fabric (A) uses proprietary protocols for FortiGate synchronization, neither is the primary vehicle for MDM data exchange. SOAP API (D) is an older protocol that has been largely replaced by REST in modern FortiNAC integrations.
"FortiNAC integrates with MDM systems by utilizing REST API communication to query the MDM database for device information. To establish this link, administrators must configure the MDM Service Connector with the appropriate API URL and authentication credentials. If the 'Test Connection' fails, verify that the FortiNAC can reach the MDM provider via the REST API port (usually HTTPS 443)." - FortiNAC-F Administration Guide: MDM Integration and Troubleshooting.
NEW QUESTION # 30
An organization wants to add a FortiNAC-F Manager to simplify their large FortiNAC-F deployment.
Which two policy types can be managed globally? (Choose two.)
- A. Endpoint Compliance
- B. Supplicant EasyConnect
- C. Network Access
- D. Authentication
Answer: A,C
Explanation:
The FortiNAC-F Manager is designed to centralize the management of multiple Control and Application (CA) appliances, ensuring consistent security posture across a distributed enterprise. To achieve this, the Manager allows administrators to define and distribute specific types of policies globally rather than configuring them on each individual CA.
According to the FortiNAC Manager Guide, the two primary policy types that are managed globally are:
Network Access Policies (D): These policies define the "If-Then" logic for network entry. By managing these at the global level, an administrator can ensure that a "Contractor" receives the same restricted access regardless of which branch office or campus they connect to.
Endpoint Compliance Policies (B): Global management of compliance policies-which consist of scans and configurations-allows for a unified security baseline. For example, a global policy can mandate that all Windows devices across the entire organization must have a specific antivirus version installed and active before gaining access to the production network.
While the Manager provides visibility into authentication events and can synchronize directory data, the specific Authentication (A) configurations (like local RADIUS secrets or specific LDAP server links) are often localized to the CA to account for site-specific infrastructure. Supplicant EasyConnect (C) is a feature set for onboarding, but the structural "Global Policy" engine focuses primarily on the Access and Compliance frameworks.
"The FortiNAC Manager enables Global Policy Management, allowing for the creation and distribution of policies across all managed CA appliances. This includes Network Access Policies, which control VLAN and ACL assignment, and Endpoint Compliance Policies, which define the security requirements for hosts. Centralizing these policies ensures that security standards are enforced uniformly across the global network fabric." - FortiNAC Manager Administration Guide: Global Policy Management Overview.
NEW QUESTION # 31
......
Fortinet NSE5_FNC_AD_7.6 Exam Practice Test Questions: https://www.practicetorrent.com/NSE5_FNC_AD_7.6-practice-exam-torrent.html
Free NSE5_FNC_AD_7.6 Braindumps Download Updated: https://drive.google.com/open?id=1XLHbJyj--RgaSbBYqNjqxiH4bB1V9Yfn