[Jun-2024] Fortinet NSE6_FSW-7.2 Actual Questions and Braindumps
Pass NSE6_FSW-7.2 Exam with Updated NSE6_FSW-7.2 Exam Dumps PDF 2024
Fortinet NSE6_FSW-7.2, also known as the Fortinet NSE 6 - FortiSwitch 7.2 exam, is a certification exam designed to test the knowledge and skills of network professionals in the field of Fortinet FortiSwitch deployment and configuration. NSE6_FSW-7.2 exam is intended for individuals who have experience working with Fortinet FortiSwitch products and are looking to demonstrate their expertise in this area. By earning this certification, candidates can enhance their career prospects and demonstrate their ability to deploy and manage Fortinet FortiSwitch products.
NEW QUESTION # 23
Which statement about the use of the switch port analyzer (SPAN) packet capture method is true?
- A. Traffic on the management interface can be mirrored and captured by the monitoring device.
- B. SPAN can be configured only on a standalone FortiSwitch.
- C. Mirrored traffic can be sent across multiple switches.
- D. The monitoring device must be connected to the same switch where the traffic is being mirrored
Answer: A
NEW QUESTION # 24
Which two rules used by MSTP are similar to rules used by other STP methods? (Choose two.)
- A. MSTP uses root bridge selection, similar to rapid STP
- B. MSTP uses port role election, similar to rapid STP on the instances.
- C. MSTP uses timers for transitioning the ports, similar to regular STP.
- D. MSTP uses alternate path and primary path, similar to regular STP.
Answer: A,D
NEW QUESTION # 25
What are two reasons why time synchronization between FortiGate and its managed FortiSwitch is critical in switch management? (Choose two.)
- A. FortiSwitch cannot complete the DTLS handshake used in the CAPWAP tunnel.
- B. FortiSwitch will not allow other FortiSwitch devices in the chain be discovered by FortiGate.
- C. FortiSwitch will not be able to become an NTP server for downstream devices.
- D. FortiSwitch does not retain its time after a reboot, which gets reset after each reboot.
Answer: A,D
NEW QUESTION # 26
Exhibit.
The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?
- A. Port23 is configured as the dedicated management interface.
- B. Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN
- C. Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.
- D. A standalone switch with the showm serial number is connected on por123.
Answer: B
NEW QUESTION # 27
How is traffic routed on FortiSwitch?
- A. Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.
- B. FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).
- C. ASIC hardware routing can only handle dynamic routing, if supported.
- D. Hardware-based routing on FortiSwitch is handled by the CPU.
Answer: B
NEW QUESTION # 28
Exhibit.
You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.
- A. Switch auto-discovery is enabled.
- B. The system time is not in-sync and is using a non-default value
- C. The FortiSwitch device is scheduled to reboot as part the authorization process
- D. The management mode was set to use FortiLink mode.
Answer: D
NEW QUESTION # 29
Exhibit.
Two routes are not installed in the forwarding information base (FIB) as shown in the exnibit. Which two statements about these two route entries are true? (Choose two.)
- A. These two routes will become primary, if the best routes are removed.
- B. These two routes will be used as load-balancing routes.
- C. These two routes are available in the hardware routing table.
- D. These two routes have a higher administrative distance value available to the destina-tion networks.
Answer: A,D
NEW QUESTION # 30
Refer to the exhibit.
Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?
- A. Access-1 is the root bridge and can only have one root port.
- B. port1 on Core-2 is discarding only management traffic.
- C. Core-1 and Core-2 do not have MCLAG configuration.
- D. Core-2 has the lowest bridge priority.
Answer: C
NEW QUESTION # 31
In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)
- A. Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.
- B. Create a virtual port pool on the FortiGate CLI.
- C. Switch the FortiLink interface to the target VDOM.
- D. Assign a port to a VDOM directly on the managed FortiSwitch.
Answer: B,D
NEW QUESTION # 32
Refer to the diagnostic output:
What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?
- A. Just the port egress payloads are printed on CLI.
- B. The types of packets captured is limited.
- C. Only untagged VLAN traffic can be captured.
- D. The switch port might be used as a trunk member
Answer: B
NEW QUESTION # 33
FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?
- A. DTLS client hello had the incorrect pre-shared key.
- B. The CAPWAP tunnel failed to come up due to a mismatch in time.
- C. The handshake process timed out before FortiSwitch responded.
- D. FortiSwitch has disabled FortiLink and is only managed as a standalone.
Answer: B
NEW QUESTION # 34
Refer to the exhibit.
The profile shown in the exhibit is assigned to a group of managed FortiSwitch ports. and these ports are connected to endpoints which are powered by PoE. Which configuration action can you perform on the LLDP profile to cause these endpoints to exchange PoE information and negotiate power with the managed FortiSwitch?
- A. Assign a new LL0P profile to handle different LLDP-ME0 TLVs
- B. Add power management as part of LLDP-MED TLVs to advertise.
- C. Create new a LLOP-MEO application type to define the PoE parameters.
- D. Define an LLDP-ME0 location 10 to use standard protocols for power.
Answer: B
NEW QUESTION # 35
Which two types of Layer 3 interfaces can participate in dynamic routing on FortiSwitch? (Choose two.)
- A. Switch virtual interfaces
- B. Physical interfaces
- C. Loopback interfaces
- D. Detected management interfaces
Answer: A,C
NEW QUESTION # 36
Which is a requirement to enable SNMP v2c on a managed FortiSwitch?
- A. Specify an SNMP host to send traps to.
- B. Create an SNMP user to use for authentication and encryption.
- C. Configure SNMP agent and communities.
- D. Enable an SNMP v3 to handle traps messages with SNMP hosts.
Answer: C
NEW QUESTION # 37
How are the 'by VLAN redirect MAC address quarantine' mode and the 'by redirect MAC address quarantine' mode on FortiGate similar?
- A. Both modes move quarantined devices to the quarantine VLAN.
- B. Both modes require firewall policies to block inter-VLAN traffic.
- C. Both modes block intra-VLAN traffic by FortiGate automatically.
- D. Both modes add quarantined device MAC addresses to the blocked firewall address group.
Answer: C
NEW QUESTION # 38
What type of multimode transceiver can be used to split a 40G port?
- A. SFP+ transceiver
- B. SFP transceiver
- C. QSFP transceiver
- D. QSFP+ transceiver
Answer: D
NEW QUESTION # 39
Exhibit.
What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)
- A. The split port can be assigned to native VLAN
- B. The FortiSwitch model is equipped with a maximum of 54 interfaces.
- C. The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.
- D. The port full speed prior the split was 100G SFP+
Answer: B,C
NEW QUESTION # 40
Which statement about the IGMP snooping querier when enabled on a VLAN is true?
- A. All other indirectly connected switches will be unable to get IGMP multicast traffic.
- B. The setting can only be enabled using the FortiSwitch CLI.
- C. IGMP reports on the VLAN are forwarded to all switch ports.
- D. Active multicast receiver entries are aging on each IGMP query sent on the VLAN
Answer: A
NEW QUESTION # 41
......
Fortinet NSE6_FSW-7.2 certification exam is an essential certification for individuals who work with FortiSwitches. It validates the skills and knowledge necessary to manage, configure, and troubleshoot FortiSwitch solutions effectively. Fortinet NSE 6 - FortiSwitch 7.2 certification is highly valued in the industry and demonstrates the candidate's commitment to their profession by staying current with the latest Fortinet technologies.
Latest NSE6_FSW-7.2 Pass Guaranteed Exam Dumps with Accurate & Updated Questions: https://www.practicetorrent.com/NSE6_FSW-7.2-practice-exam-torrent.html
NSE6_FSW-7.2 Exam Brain Dumps - Study Notes and Theory: https://drive.google.com/open?id=1fysBpbBCgVxJeJkTgWWu7Inpgsv9WaDv