200-301 Exam Dumps - PDF Questions and Testing Engine [Q532-Q552]

200-301 Exam Dumps - PDF Questions and Testing Engine

200-301 Dumps - The Sure Way To Pass Exam

NEW QUESTION # 532
Refer to the exhibit.

Router R2 is configured with multiple routes to reach network 10 1.1 0/24 from router R1. What protocol is chosen by router R2 to reach the destination network 10.1 1 0/24?

A. eBGP
B. EIGRP
C. static
D. OSPF

Answer: C

NEW QUESTION # 533
Drag and drop the AAA functions from the left onto the correct AAA services on the right

Answer:

Explanation:

NEW QUESTION # 534
Refer to the exhibit.

An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.

Answer:

Explanation:

NEW QUESTION # 535
in Which way does a spine and-leaf architecture allow for scalability in a network when additional access ports are required?

A. A spine switch can be added with at least 40 GB uplinks
B. A spine switch and a leaf switch can be added with redundant connections between them
C. A leaf switch can be added with a single connection to a core spine switch.
D. A leaf switch can be added with connections to every spine switch

Answer: D

Explanation:
Spine-leaf architecture is typically deployed as two layers: spines (such as an aggregation layer), and leaves (such as an access layer). Spine-leaf topologies provide high-bandwidth, low-latency, nonblocking server-to-server connectivity.
Leaf (aggregation) switches are what provide devices access to the fabric (the network of spine and leaf switches) and are typically deployed at the top of the rack. Generally, devices connect to the leaf switches.
Devices can include servers, Layer 4-7 services (firewalls and load balancers), and WAN or Internet routers.
Leaf switches do not connect to other leaf switches. In spine-and-leaf architecture, every leaf should connect to every spine in a full mesh.
Spine (aggregation) switches are used to connect to all leaf switches and are typically deployed at the end or middle of the row. Spine switches do not connect to other spine switches.

NEW QUESTION # 536
Refer to the exhibit.

The default-information originate command is configured under the R1 OSPF configuration. After testing, workstations on VLAN 20 at Site B cannot reach a DNS server on the Internet.
Which action corrects the configuration issue?

A. Add the default-information originate command on R2.
B. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.18 command on R1.
C. Add the always keyword to the default-information originate command on R1.
D. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.2 command on R2.

Answer: B

NEW QUESTION # 537
Drag the descriptions of device management from the left onto the types of device management on the right.

Answer:

Explanation:

Cisco DNA Center Device Management
3. Monitor the cloud for software update
5. Uses CLI templates to apply a consistent configuration to multiple devices at an individual location
6. Uses NetFlow to analyse potential security threats throughout the network and take appropriate action on that traffic Traditional device management
2. Manages device configuration on a per-device basis
4. Security is managed near the perimeter of the network with firewalls, VPNs, and IPS Implements changes via an SSH terminal

NEW QUESTION # 538
R1 has learned route 192.168.12.0/24 via IS-IS, OSPF, RIP, and Internal EIGRP.
Under normal operating conditions, which routing protocol is installed in the routing table?

A. RIP
B. Internal EIGRP
C. IS-IS
D. OSPF

Answer: B

NEW QUESTION # 539
Refer to the exhibit.

Which password must an engineer use to enter the enable mode?

A. cisco123
B. adminadmin123
C. default
D. testing 1234

Answer: D

NEW QUESTION # 540
Refer to the exhibit.

Load-balanced traffic is coming in from the WAN destined to a host at 172.16.1.190. Which next-hop is used by the router to forward the request?

A. 192.168.7.40
B. 192.168.7.4
C. 192.168.7.35
D. 192.168.7.7

Answer: A

NEW QUESTION # 541
What Is a syslog facility?

A. group of log messages associated with the configured severity level
B. password that authenticates a Network Management System to receive log messages
C. Host that is configured for the system to send log messages
D. set of values that represent the processes that can generate a log message

Answer: A

Explanation:
Explanation
Cisco Community - Difference between logging level and logging facility Post by ahmednaas
"The logging facility command basically tells the syslog server where to put the log message. You configure the syslog server with something like:
local7.debug /var/adm/local7.log
Now, when you use the "logging facility local7" on your device, all messages with severity "debug" or greater should be saved in /var/adm/local7.log.
Example: on a switch, any process (CDP, SNMP, etc.) can generate a log message. On a syslog server, the logging facility is the place where all received messages with the same priority level are stored.

NEW QUESTION # 542
Refer to the exhibit.

How many objects are present in the given JSON-encoded data?

A. nine
B. four
C. one
D. seven

Answer: B

NEW QUESTION # 543
Which command is used to specify the delay time in seconds for LLDP to initialize on any interface?

A. lldp holdtimt
B. lldp reinit
C. lldp timer
D. lldp tlv-select

Answer: D

NEW QUESTION # 544
Which three features are added in SNMPv3 over SNMPv2?

A. Message Integrity
B. Compression
C. Authentication
D. Error Detection
E. Encryption

Answer: A,C,E

NEW QUESTION # 545
Drag and Drop Question
Drag and drop the Ansible terms from the left onto the right.

Answer:

Explanation:

NEW QUESTION # 546
How does HSRP provide first hop redundancy?

A. It load-balances Layer 2 traffic along the path by flooding traffic out all interfaces configured with the same VLAN.
B. It load-balances traffic by assigning the same metric value to more than one route to the same destination in the IP routing table.
C. It forwards multiple packets to the same destination over different routed links in the data path.
D. It uses a shared virtual MAC and a virtual IP address to a group of routers that serve as the default gateway for hosts on a LAN.

Answer: D

NEW QUESTION # 547
Refer to Exhibit.

IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:
1. Configure reachability to the switch SW1 LAN subnet in router R2.
2. Configure default reachability to the Internet subnet in router R1.
3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.
4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1. and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.

Answer:

Explanation:
Answer as below configuration:
On R2:
Enable
Conf t
Ip route 192.168.1.0 255.255.255.0 10.10.31.1
On R1:
Enable
Conf t
Ip route 0.0.0.0 0.0.0.0 10.10.13.3
On R2
Ip route 172.20.20.128 255.255.255.128 e0/2
Ip route 172.20.20.128 255.255.255.128 e0/1
On R1
Ip route 192.168.0.0 255.255.255.0 e0/1
Ip route 192.168.0.0 255.255.255.0 10.10.12.2 3
Save all configurations after every router from anyone of these command Do wr Or Copy run start

NEW QUESTION # 548
Refer to the exhibit.

If configuring a static default route on the router with the ip route 0.0.0.0 0.0.0.0 10.13.0.1 120 command how does the router respond?

A. It starts sending traffic without a specific matching entry in the routing table to GigabitEthernetO/1
B. It ignores the new static route until the existing OSPF default route is removed
C. It starts load-balancing traffic between the two default routes
D. It immediately replaces the existing OSPF route in the routing table with the newly configured static route

Answer: B

Explanation:
Explanation
Our new static default route has the Administrative Distance (AD) of 120, which is bigger than the AD of OSPF External route (O*E2) so it will not be pushed into the routing table until the current OSPF External route is removed.For your information, if you don't type the AD of 120 (using the command "ip route 0.0.0.0
0.0.0.0 10.13.0.1") then the new static default route would replace the OSPF default route as the default AD of static route is 1. You will see such line in the routing table:S* 0.0.0.0/0 [1/0] via 10.13.0.1

NEW QUESTION # 549
Refer to Exhibit.

Rotor to the exhibit. The IP address configurations must be completed on the DC-1 and HQ-1 routers based on these requirements:
DC-1 Gi1/0 must be the last usable address on a /30
DC-1 Gi1/1 must be the first usable address on a /29
DC-1 Gi1/2 must be the last usable address on a /28
HQ-1 Gil/3 must be the last usable address on a /29
Drag and drop the commands from the left onto the destination interfaces on the right. Not all commands are used