Verified 200-301 dumps Q&As 100% Pass in First Attempt Guaranteed Updated Dump from PracticeTorrent
Pass CCNA 200-301 Exam With 920 Questions
Cisco 200-301 exam is also an excellent starting point for those who wish to pursue a career in networking. It provides a solid foundation in networking concepts and technologies, which can help candidates to build a successful career in IT. The CCNA certification is also a prerequisite for many other Cisco certifications, such as the Cisco Certified Network Professional (CCNP) and the Cisco Certified Internetwork Expert (CCIE).
The CCNA certification is a highly sought-after credential in the IT industry. It demonstrates to employers that you have the skills and knowledge necessary to design, implement, and manage complex network infrastructures. CCNA certified professionals are in high demand across a variety of industries, including healthcare, finance, telecommunications, and technology.
NEW QUESTION # 69
Refer to the exhibit.
The default-information originate command is configured under the R1 OSPF configuration After testing workstations on VLAN 20 at Site B cannot reach a DNS server on the Internet Which action corrects the configuration issue?
- A. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.18 command on R1
- B. Add the always keyword to the default-information originate command on R1
- C. Configure the ip route 0.0.0.0 0.0.0.0 10.10.10.2 command on R2
- D. Add the default-information originate command onR2
Answer: B
NEW QUESTION # 70
Refer to the exhibit. R5 is the current DR on the network, and R4 is the BDR. Their interfaces are flapping, so a network engineer wants the OSPF network to elect a different DR and BDR. Which set of configurations must the engineer implement?
- A. R4(config)#interface gi0/0
R4(config-if)#ip ospf priority 20
R5(config)#interface gi0/0
R5(config-if)#ip ospf priority 10 - B. R3(config)#interface gi0/0
R3(config-if)#ip ospf priority 255
R2(config)#interface gi0/0
R2(config-if)#ip ospf priority 240 - C. R2(config)#interface gi0/0
R2(config-if)#ip ospf priority 259
R3(config)#interface gi0/0
R3(config-if)#ip ospf priority 256 - D. R5(config)#interface gi0/0
R5(config-if)#ip ospf priority 120
R4(config)#interface gi0/0
R4(config-if)#ip ospf priority 110
Answer: B
NEW QUESTION # 71
Drag and drop the IPv6 address type characteristics from the left to the right.
Answer:
Explanation:
NEW QUESTION # 72
Refer to the exhibit.
Router R1 is running three different routing protocols. Which route characteristic is used by the router to forward the packet that it receives for destination IP 172.16.32.1?
- A. cost
- B. administrative distance
- C. longest prefix
- D. metric
Answer: C
Explanation:
https://learningnetwork.cisco.com/s/question/0D53i00000KszSlCAJ/administrative-distance-vs-longest-match-rule
NEW QUESTION # 73
Drag and drop the characteristics of northbound APIs from the left onto any position on the right. Not all characteristics are used.
Answer:
Explanation:
NEW QUESTION # 74
Lab Simulation 5
All physical cabling between the two switches is installed. Configure the network connectivity between the switches using the designated VLANs and interfaces.
1. Configure VLAN 100 named Compute and VLAN 200 named Telephony where required for each task.
2. Configure Ethernet0/1 on SW2 to use the existing VLAN named Available.
3. Configure the connection between the switches using access ports.
4. Configure Ethernet0/1 on SW1 using data and voice VLANs.
5. Configure Ethemet0/1 on SW2 so that the Cisco proprietary neighbor discovery protocol is turned off for the designated interface only.
Answer:
Explanation:
on sw1
enable
conf t
vlan 100
name Compute
vlan 200
name Telephony
int e0/1
switchport voice vlan 200
switchport access vlan 100
int e0/0
switchport mode access
do wr
on sw2
Vlan 99
Name Available
Int e0/1
Switchport access vlan 99
do wr
NEW QUESTION # 75
Refer to the exhibit.
Which per-hop QoS behavior is R1 applying to incoming packets?
- A. queuing
- B. policing
- C. shaping
- D. marking
Answer: B
Explanation:
Explanation
R1 is applying policing to incoming packets. Policing is a QoS mechanism that limits the rate of traffic flow by dropping or remarking packets that exceed the configured rate limit. In this case, R1 is applying policing to incoming packets on interface G0/0 and G0/1. The exhibit shows that R1 is configured to police traffic at a rate of AF31, AF21, and AF11. This means that R1 is limiting the rate of traffic flow for these three traffic classes .
References:
Cisco CCNA Certification Guide - Chapter 16: Quality of Service (QoS)
Cisco IOS Quality of Service Solutions Configuration Guide - Configuring Class-Based Policing
NEW QUESTION # 76
Drag and drop the statements about networking from the left onto the corresponding networking types on the right.
Answer:
Explanation:
Explanation
A picture containing table Description automatically generated
NEW QUESTION # 77
Drag and drop the QoS terms from the left onto the descriptions on the right.
Answer:
Explanation:
NEW QUESTION # 78
Which command entered on a switch configured with Rapid PVST* listens and learns for a specific time period?
- A. switch(config)#spanning-tree vlan 1 hello-time 10
- B. switch(config)#spanning-tree vlan 1 forward-time 20
- C. switch(config)#spanning-tree vlan 1 priority 4096
- D. switch(config)#spanning-tree vlan 1 max-age 6
Answer: B
Explanation:
Forward time : Determines how long each of the listening and learning states last before the port begins forwarding.
Switch(config)# [ no ] spanning-tree vlan vlan_ID forward-time forward_time Configures the forward time of a VLAN.
The forward_time value can be from 4 to 30 seconds.
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/15-02SG/configuration/guide/config/spantree.html#56177
NEW QUESTION # 79
Which protocol is used in Software Defined Access (SDA) to provide a tunnel between two edge nodes in different fabrics?
- A. Virtual Local Area Network (VLAN)
- B. Virtual Extensible LAN (VXLAN)
- C. Generic Router Encapsulation (GRE)
- D. Point-to-Point Protocol (PPP)
Answer: B
Explanation:
Section: Automation and Programmability
Explanation/Reference:
NEW QUESTION # 80
What is the purpose of a southbound API in a control based networking architecture?
- A. allows application developers to interact with the network
- B. integrates a controller with other automation and orchestration tools.
- C. Facilities communication between the controller and the applications
- D. Facilities communication between the controller and the networking hardware
Answer: D
Explanation:
Explanation
https://www.ciscopress.com/articles/article.asp?p=2995354&seqNum=2#:~:text=The%20Southbound%20Interfa The Southbound Interface In a controller-based network architecture, the controller needs to communicate to the networking devices.
NEW QUESTION # 81
Refer to the exhibit.
which path is used by the router for internet traffic ?
- A. 10.10.10.0/28
- B. 0.0.0.0/0
- C. 10.10.13.0/24
- D. 209.165.200.0/27
Answer: B
NEW QUESTION # 82
Refer to the exhibit.
Which two configurations must the engineer apply on this network so that R1 becomes the DR? (Choose two.) A)
B)
C)
D)
E)
- A. Option D
- B. Option C
- C. Option A
- D. Option E
- E. Option B
Answer: B,E
NEW QUESTION # 83
Which two options will help to solve the problem of a network that is suffering a broadcast storm?
(Choose two.)
- A. a bridge
- B. a router
- C. a Layer 3 switch
- D. an access point
- E. a hub
Answer: B,C
NEW QUESTION # 84
Refer to the exhibit. The link between PC1 and the switch is up, but it is performing poorly.
Which interface condition is causing the performance problem?
- A. There is a speed mismatch on the interface.
- B. There is an issue with the fiber on the switch interface.
- C. There is a duplex mismatch on the interface
- D. There is an interface type mismatch
Answer: C
Explanation:
The PC's port runs in full duplex, while the Fa0/1 port on the switch is in auto-negotiate mode.
This results in a duplex mismatch that causes the switchport to operate as half-duplex, which culminates in poor performance on the link.
"A duplex mismatch occurs when two connected devices are configured in different duplex modes.
This may happen, for example, if one is configured for autonegotiation while the other one has a fixed mode of operation that is full duplex (no autonegotiation). In such conditions, the autonegotiation device correctly detects the speed of operation, but is unable to correctly detect the duplex mode.
As a result, it sets the correct speed but assumes half-duplex mode.
When a device is operating in full duplex while the other one operates in half duplex, the connection works reliably only at a very low throughput." Reference: https://en.wikipedia.org/wiki/Autonegotiation#Duplex_mismatch
NEW QUESTION # 85
Drag and drop the functions from the left onto the correct network components on the right
Answer:
Explanation:
NEW QUESTION # 86
Which command sequence can you enter to create VLAN 20 and assign it to an interfaceon a switch?
- A. Switch (config)#Interface gig x/y Switch (config-if)#vlan 20 Switch (config-vlan)#switchport access vlan 20
- B. Switch (config)#vlan 20 Switch (config)#Interface vlan 20 Switch (config-if)#switchport access vlan 20
- C. Switch (config)#vlan 20 Switch (config)#Interface vlan 20 Switch (config-if)#switchport trunk native vlan 20
- D. Switch (config)#vlan 20 Switch (config)#Interface gig x/y Switch (config-if)#switchport access vlan 20
- E. Switch (config)#vlan 20 Switch (config)#Interface vlan 20 Switch (config-if)#switchport trunk allowed vlan 20
Answer: D
NEW QUESTION # 87
......
Ultimate Guide to Prepare Free 200-301 Exam Questions and Answer: https://drive.google.com/open?id=1QlVVDxNBkUuX40Wz1a3PhVFZ4hzLk5K-
Pass 200-301 Tests Engine pdf - All Free Dumps: https://www.practicetorrent.com/200-301-practice-exam-torrent.html